Tail lamp connector 6 PIN Jumper, Boxer, Ducato

Compatibility with Models

• FIAT Ducato: years 2006-2010
• PEUGEOT Boxer: years 2006-2010
• CITROEN Jumper: years 2006-2010

Contents of the Kit

• 1 x Plastic connector housing
• 6 x Connectors/Pins

Purpose of the Repair Connector

6 PIN rear lamp connector is used to repair the electrical connection between the vehicle's wiring harness and the rear lamp. It is useful when replacing a damaged connector, loose or corroded contacts, and when recreating the connection after local overheating of the connector.

This solution allows for the repair of the plug itself without the need to replace the entire wiring harness, provided that its other components are functional.

When should the lamp connector be replaced?

A damaged or loose electrical connection of the lamp can cause, among other things:

• intermittent loss of rear lighting,
• flashing or improper operation of some lights,
• messages about a faulty bulb despite its proper condition,
• signs of corrosion, burning, or overheating on the pins and housing,
• unstable connection when moving the harness.

Note: such symptoms may also result from a damaged ground, bulb socket, wires, or the lamp itself. The actual cause of the fault should be determined before repair.

Benefits of Using the Repair Kit

• The ability to replace a damaged plug housing without replacing the entire installation.
• Replacement of worn contacts with new connectors.
• Localized repair focused on the damaged connection.
• Useful for both DIY electrical installation work and workshop repairs.
• The possibility of using existing wires if they are in good condition and suitable for re-termination.

Product Identification CCY

• CCY Catalog Number: 330792
• GTIN Code: 5908258867602
• Part Type: repair element for automotive lighting installation.
• Mounting Type: seating connectors on wires and placing them in the connector housing.

Installation Tips

1. Turn off the ignition and secure the electrical installation against accidental power supply; if necessary, disconnect the battery according to the vehicle manufacturer's procedure.
2. Before unplugging the old connector, document the position of each wire and its function. If in doubt, refer to the electrical diagram of the specific vehicle.
3. Check the condition of the wires and contacts on the lamp side. Burned or loose contacts on both sides require the cause of the fault to be addressed.
4. Prepare the ends of the wires and crimp new connectors with the appropriate crimping tool suited to their type and wire gauge.
5. Seat the connectors in the appropriate chambers of the housing; check that they are properly locked and do not pull out with a light tug.
6. Secure the repaired wires and route the harness so that it is not exposed to abrasion, tension, or moisture.
7. After installation, check the operation of all functions of the rear lamp present in the specific version of the vehicle.

Important: do not determine the order of wires based solely on the color of the insulation. The assignment of contacts must correspond to the original connection in the specific vehicle.

What to pay attention to before purchasing?

• Compare the shape of the housing, guides, latch, and socket layout with the original connector.
• Check the actual number of used contacts in the vehicle; depending on the vehicle's design, there may be different variants of rear lamp connectors.
• Verify the side of the vehicle and the version and equipment of the lamp if there are differences in the installation.
• Do not base the selection solely on the model name and year — the compatibility of the physical connector is decisive.

If the appearance of the old connector is ambiguous, it is advisable to send a photo of the plug from the contact and latch side before purchasing.

Version without wires vs. ready harness

The offered kit is intended for self-termination of existing wires. It is not a ready harness with factory-mounted cable sections.

If the damage also includes wires over a greater length, a version with wires, available from CCY as a separate product no. 330790, may be a more convenient solution. Before choosing, check the compatibility of both versions with the lamp socket.

Frequently Asked Questions (FAQ)

Can this kit be used if the old connector is melted?
Yes, provided that the new housing fits the lamp and the repair also includes damaged wires and contacts. The cause of overheating should be checked, especially the condition of the ground connection.

Is the kit ready to plug in without using tools?
No. The connectors require proper attachment to the wires and seating in the housing.

Do I need to replace the entire rear lamp?
Not always. If only the connector of the harness is damaged, and the contacts and other components of the lamp are functional, usually repairing the connection is sufficient. If the lamp contact is also damaged, it requires separate repair or replacement of the appropriate part.

Does the connector fit every example of the mentioned models?
This cannot be guaranteed without comparing the plug. Before purchasing, check its physical shape and locking mechanism.